Lumi Industries

3D Printing resins, filaments and materials

Lumi Industries sells LumiReact 3D printing resins, Fep, post processing products and filaments. Official Italian distributor of Fun To Do 3D printing resins .

FTD Standard Blend 3D Printing resin

FTD Standard Blend 3D Printing resin


Fun To Do 3D printing multi-purpose resin. 3 colors available.

Add to Cart

3D printing resin Fun To Do Standard Blend.

Fun To Do real multi purpose resin, most cost effective for printing your day to day objects.

The Standard Blend resin works with any light source with a wavelength of 225nm to 415nm – this means there is no need to modify DLP 3D printers. Standard Blend resin also work reliably with some models of SLA printers.

Please note: we do not recommend the use of Unpigmented Standard Blend resin with the LumiPocket and Lumiforge 3D printers.

Super speed

A DLP Printer with a 180 watt lamp will cure a 0.05mm layer in approximately 2 seconds. A 240 watt lamp will cure a 0.05mm layer in half a second. With the Standard Blend resin you have hardening times among the fastest of all the resins on the market.

Super easy to use

The Standard Blend resin comes ready to use with pigments already optimised and mixed in.
After initial calibration, there is nothing else to worry about. Special formulation has brought down average shrinkage on these resins to approximately 0.5% (the industry average is 3.5%).

The Standard Blend resin have a very faint odour and cause minimal skin irritation as compared to other resins.

Super strong

When fully cured the Standard Blend resin has a hardness of approximately 35 shore D (what does this mean?). Standard Blend resin has also been tested and proven to withstand a myriad of different chemicals including water, acetone, alcohol and thinner.

3D printing resin Fun To Do Standard Blend characteristics

 Package    1 kg
 Color    translucent
 Viscosity        at 25°C         100 mPa.s
 Density    1.02 g/cm3
 Hardness (Shore D)         35

Finishing Instructions

  1. To clean and remove excess resin, agitate the 3D printed part in an ulkltrasonic cleaner with TEK1969 cleaning or in a simple vat with TEK1960 solvent* for 1-2 minutes until all excess resins has been removed.

  2. Do not soak in acetone. Do not leave the 3D part soaking in the liquid. Use a soft brush if necessary.

  3. Clean off any excess of liquid with a cold blowdryer or compressed air.

  4. Leave under the sun or in a UV lamp to cure. The resin is fully cured when fingernails do not leave scratch marks on the object.

  5. Even after full post cure some parts may still have a sticky surface. You can treat your print with Ta-Tack Away. A quick wash in this special formula will add a stick-free coating on the printed part.

*We do not recommend the use of denatured or isopropyl alcohol (IPA). It is very aggressive on the polymerized resin and it could weaken the structure of the 3D part. It is also flammable and potentially harmful to people and the environment.

Store the resin in a dry, cool, shaded place out of direct sunlight.

More information about Standard Blend is available at FunToDo.

Fun To Do Standard Blend NEXT GENERATION

Because of the world wide shortage of some ingredients, Fun To Do has not been able to supply distributors and resellers all over the world with the full range of products. This is why they have developed alternative formulas, using ingredients that they can source easily. This way they can circumvent shortages that might appear in future times.

With these new formulations they have tried to copy the properties of their existing products, but the properties of the new formulas, although similar, are not the same.  Some of the NxtGen products are stronger, some of the products are faster on one machine, and the same, or perhaps a bit slower at a certain layer thickness, on another machine.

In periods of raw material shortages, you might receive NXT GEN formulas instead of the classic one